Accredited High Voltage Auditing

We are here to Help you - need high voltage auditing done in Queensland give us a call
1

High Voltage Audit Requirements

Owners of high voltage Installations have responsibilities to ensure safe operation of their electrical infrastructure. Periodic inspections can prolong the lifetime of the equipment while correct operating procedures and meeting Australian Standards compliance regulations. BDD's  accedited high voltage compliance audit and installation safety management service provides 3rd party audits of customers high voltage installations, protection and ancillary equipment supported by documentation that outlines customers electrical systems. The report advise customers how to rectify areas of non-compliance, suggested remedial actions and compliance information for Service and Installation Rules and relevant standards.

When do I need a High Voltage Audit?

All new or modified installations must have a high voltage audit completed to comply withe the Qld electrical safety act, however in the real world this only partially covers the requirements as things get changed added and repaired and often leaves the once complaint installation very much lacking and unsafe - Protection and safety clearances are normally the worst offending problems. Periodic Audits is the best way to ensure the installation meets safety requirements and ensures both plant and workers remain as safe as possible. We do Draglines shovels Transmission Lines, Substations and High Voltage Motors as well as switchboards RMU's and ancillary equipment.
2
3

Existing High Voltage Equipment

As we all know everything has a lifecycle and is prone to damage and wear.  Powelines crossarms always end up rotting splitting and sometimes it just wasnt put in correctly in the first place.  Give us a call here and we can organise a cycle to get your equipment checked to give you peace of mind and minimal breakdowns

Connection and reconnection of high voltage systems

This information  gives advice that is practical information about legislative requirements for owners of high voltage installations. To look for the actual conditions that are legislative please refer to the Electrical protection Act 2002 plus the electric Safety Regulation 2002. What exactly is a voltage installation that is high? A voltage that is high is a small grouping of components of electrical equipment permanently connected together and supplied with electricity at voltages greater than 1000VAC RMS or 1500V ripple-free DC.
Examples of high voltage systems
Organizations that take electricity supply greater than 1000VAC RMS or 1500 ripple free DC direct from the electricity distributor, or have portions of their electrical installation operating at such voltages, have actually high voltage installations – for example shopping centers or big manufacturing sites that have a high voltage transformer and switchgear onsite powering there installation.
4
5

Penalties for offences (Not getting a High Voltage Audit )

Failure to adhere to the obligations under part 27 regarding the Electrical Safety Act 2002 may end in legal proceedings that may include charges up to $1,000,000 ($200,000 for an individual) or three years imprisonment. Under area 153 of the Electrical protection Regulation 2002, a person must not connect or reconnect a top voltage electrical installation to a way to obtain electricity, after electrical work has been performed on the installation, unless the electric work was inspected by a certified auditor and found to be electrically safe and compliant with the Wiring Rules (AS/NZS 3000) and other relevant Australian standards, such as AS 2067 (Substations and high voltage installations surpassing 1 kV a.c.).

Obligations and responsibilities for High Voltage Systems

The owner of the voltage that is high must ensure that: • the installation is inspected, tested and discovered to be electrically safe by an accredited auditor before the installation is connected or reconnect to the electricity supply; and • all requirements, as stipulated by the accredited auditor, are met and are maintained during the life of the installation. The responsibility is had by the owner to: • accept or reject the style and gear found in the installation, ensuring compliance with legislative and Australian standard requirements; and • accept the use of any particular equipment or way of installation in respect with, and ensuring compliance with, legislative and Australian standard requirements, and to obtain advice on this from people competent to provide advice that is such. Exactly what must your accredited auditor do? • inspect the voltage that is high installation, confirm the installation has been tested to ensure it's electrically safe and is in respect with the Wiring Rules along with other appropriate Australian requirements; and • provide written notification to the dog owner / occupier or even to their representative detailing the outcome of the assessment; and • the auditor, or the employer of the accredited auditor, must make and keep a copy of the examination report for at least five years.
6